A Comparison Study of Fatigue Behavior of S355J2+N, S690QL and X37CrMoV5-1 Steel

Једноставна страница ставке
dc.citation.spage1199
dc.citation.volume12
dc.contributor.authorMilovanović, Vladimir
dc.contributor.authorArsić, Dušan
dc.contributor.authorMilutinović, Miroslav
dc.contributor.authorŽivković, Miroslav
dc.contributor.authorTopalović, Marko
dc.date.accessioned2023-05-11T11:12:07Z
dc.date.available2023-05-11T11:12:07Z
dc.date.issued2022
dc.description.abstractSteel of the mild-strength S355J2+N steel grade is the most often used steel for manufacturing carrying sections of constructions exposed to fatigue loads. The use of high-strength steels, such as S690QL, allows for the creation of structures that are light and simple to construct. However, increasing the yield strength of high-strength steels does not result in a corresponding increase in fatigue resistance. As a result, using high-strength steels for constructions subjected to fatigue loading can be a major design concern, raising the question of whether high-strength steels should be used at all. Most of the experimental investigations regarding the hot work tool steel X37CrMoV5-1 found in the literature are focused on its machining and wear resistance, with insufficient attention paid to the cyclic loads. This article evaluates the fatigue properties of mild-strength S355J2+N, high-strength S690QL, and X37CrMoV5-1 steel grades. A SHIMADZU servo-hydraulic testing machine is used to perform uniaxial tensile tests under uniaxial fatigue stress-controlled, fully reversed conditions (tensile–compression testing with R = 􀀀1 stress ratio) in accordance with EN ISO and ASTM standards. The aim of this paper is to highlight the fatigue characteristics of these three steels that are among the most used in their respective groups. Steel S355J2+N belongs to the group of hot-rolled normalized steels, S690QL belongs to the group of improved (quenched + tempered) steels with increased strength, and X37CrMoV5-1 belongs to the group of high-alloyed tool steels for hot work. This choice was made as the tested steels can be considered typical representatives of their groups. Based on the test results of these three steels, which are organized in S–N curves, the fatigue behavior of the entire mentioned groups of steels can be foreseen.
dc.identifier.doi10.3390/met12071199
dc.identifier.urihttps://vaseljena.ues.rs.ba/handle/123456789/128
dc.language.isoen
dc.publisherMDPI
dc.sourceMetals
dc.subjectstructural fatigue tests; fatigue life; S–N fatigue curves; S355J2+N steel grade; S690QL steel grade; STRENX 700 steel grade; X37CrMoV5-1 steel grade; AISI H11 steel grade
dc.titleA Comparison Study of Fatigue Behavior of S355J2+N, S690QL and X37CrMoV5-1 Steel
dc.typeArticle
Датотеке
Оригинални завежљај
Сада се приказује 1 - 1 од 1
Сличица
Име:
A Comparison Study of Fatigue Behavior of S355J2+N, S690QL.pdf
Величина:
3.65 MB
Формат:
Adobe Portable Document Format
Опис:
Преузимање
Свежањ лиценце
Сада се приказује 1 - 1 од 1
Сличица
Име:
license.txt
Величина:
1.71 KB
Формат:
Item-specific license agreed to upon submission
Опис:
Преузимање
Колекције
Машински факултет [Научни радови] / Faculty of Mechanical Engineering [Scientific papers]